The i2c_polling_b2b_slave example shows how to use i2c driver as slave to do board to board transfer with a polling master:In this example, one i2c instance as slave and another i2c instance on the other board as master. Master sends a piece of data to slave, and receive a piece of data from slave. This example checks if the data received from slave is correct.

The MRT project is a simple demonstration program of the SDK MRT driver. It sets up the MRThardware block to trigger a periodic interrupt after every 250 milliseconds. When the PIT interrupt is triggereda message a printed on the UART terminal and an LED is toggled on the board.

The power_mode_switch application shows the usage of normal power mode control APIs for entering the three kinds oflow power mode: Sleep mode, Deep Sleep mode and Power Down mode, deep power down mode. When the application runs to each low powermode, the device would cut off the power for specific modules to save energy. The device can be also waken up by prepared wakeup source from external event. Tips: This demo is to show how the various power mode can switch to each other. However, in actual low power use case, to save energy and reduce the consumption even more, many things can be done including: - Disable the clock for unnecessary module during low power mode. That means, programmer can disable the clocks before entering the low power mode and re-enable them after exiting the low power mode when necessary. - Disable the function for unnecessary part of a module when other part would keep working in low power mode. At the most time, more powerful function means more power consumption. For example, disable the digital function for the unnecessary pin mux, and so on. - Set the proper pin state (direction and logic level) according to the actual application hardware. Otherwise, the pin cirrent would be activied unexpectedly waste some energy. - Other low power consideration based on the actual application hardware. - In order to meet typedef power consumption of DateSheet manual, Please configure MCU under the following conditions. 鈥? Configure all pins as GPIO with pull-up resistor disabled in the IOCON block. 鈥? Configure GPIO pins as outputs using the GPIO DIR register. 鈥?Write 1 to the GPIO CLR register to drive the outputs LOW. 鈥?All peripherals disabled.

The SCTimer 16-bit counter project is a demonstration program of the SDK SCTimer driver operation when using the SCTimer counteras two 16-bit counters.The example toggles an output per counter when a match occurs.

This SCTIMer project is a demonstration program of the SDK SCTimer driver's PWM generation. It sets up a PWM signaland periodically updates the PWM signals dutycycle.

The SCTimer project is a simple demonstration program of the SDK SCTimer's driver capabiltiy to generate PWM signals.

The spi_interrupt_master example shows how to use spi functional API to do interrupt transfer as a master:In this example, the spi instance as master. Master sends a piece of data to slave, receive data from slave,and check if the data master received is correct. This example needs to work with spi_interrupt_slave example.

The spi_interrupt_slave example shows how to use spi driver as slave to receive data from master.In this example, one spi instance as slave and another spi instance on other board as master. Master sends a piece of data to slave, and receive a piece of data from slave. This example checks if the data received from master is correct. This example should work with spi_interrupt_master example. And this example should start first.

The spi_polling_transfer_master example shows how to use spi driver as master to do board to boardtransfer with polling:In this example, one spi instance as master and another spi instance on othere board as slave. Mastersends a piece of data to slave, and receive a piece of data from slave. This example checks if the data received from slave is correct. This example need to work with spi_polling_transfer_slave example.

The spi_polling_transfer_slave example shows how to use spi driver as slave to receive data from master.In this example, one spi instance as slave and another spi instance on other board as master. Master sends a piece of data to slave, and receive a piece of data from slave. This example checks if the data received from master is correct. This example should work with spi_polling_transfer_master example. And this example should start first.