The FTM project is a simple demonstration program of the SDK FTM driver to use FTM as a timer.It sets up the FTM hardware block to trigger an interrupt every 1 millisecond.When the FTM interrupt is triggered a message a printed on the UART terminal.

The GPIO Example project is a demonstration program that uses the KSDK software to manipulate the general-purposeoutputs.The example is supported by the set, clear, and toggle write-only registers for each port output data register. The example take turns to shine the LED.

The Hello World demo application provides a sanity check for the new SDK build environments and board bring up. The HelloWorld demo prints the "Hello World" string to the terminal using the SDK UART drivers. The purpose of this demo is toshow how to use the UART, and to provide a simple project for debugging and further development.

The LED Blinky demo application provides a sanity check for the new SDK build environments and board bring up. The LED Blinky demo uses the systick interrupt to realize the function of timing delay. The example takes turns to shine the LED. The purpose of this demo is to provide a simple project for debugging and further development.

The LPTMR project is a simple demonstration program of the SDK LPTMR driver. It sets up the LPTMRhardware block to trigger a periodic interrupt after every 1 second. When the LPTMR interrupt is triggereda message a printed on the UART terminal and an LED is toggled on the board.

The fee_bple example shows how to use MCG driver to change from FEE mode to BLPE mode: 1. How to use the mode functions for MCG mode switch. 2. How to use the frequency functions to get current MCG frequency. 3. Work flow Boot to Fee mode from default reset mode Change from FEE -> FBE -> BLPE Change back BLPE -> FBE -> FEE Get System clock in FEE mode to blink LEDIn this example, because the debug console's clock frequency may change,so the example running information is not output from debug console. Here theLED blinks to show that the example finished successfully.

The fee_bpli example shows how to use MCG driver to change from FEE mode to BLPI mode: 1. How to use the mode functions for MCG mode switch. 2. How to use the frequency functions to get current MCG frequency. 3. Work flow Boot to FEE mode from default reset mode Change from FEE -> FBI -> BLPI Change back BLPI -> FBI -> FEE Get System clock in FEE mode to blink LEDIn this example, because the debug console's clock frequency may change,so the example running information is not output from debug console. Here theLED blinks to show that the example finished successfully.

The fei_bpli example shows how to use MCG driver to change from FEI mode to BLPI mode: 1. How to use the mode functions for MCG mode switch. 2. How to use the frequency functions to get current MCG frequency. 3. Work flow Boot to FEI mode from default reset mode Change mode FEI -> FBI -> BLPI Change back BLPE -> FBI -> FEI Get System clock in FEI mode to blink LEDIn this example, because the debug console's clock frequency may change,so the example running information is not output from debug console. Here theLED blinks to show that the example finished successfully.

The pee_bple example shows how to use MCG driver to change from PEE mode to BLPE mode: 1. How to use the mode functions for MCG mode switch. 2. How to use the frequency functions to get current MCG frequency. 3. Work flow Boot to PEE mode from default reset mode Change mode PEE -> PBE -> BLPE Change back BLPE -> PBE -> PEE Get System clock in PEE mode to blink LEDIn this example, because the debug console's clock frequency may change,so the example running information is not output from debug console. Here theLED blinks to show that the example finished successfully.

The pee_bpli example shows how to use MCG driver to change from PEE mode to BLPI mode: 1. How to use the mode functions for MCG mode switch. 2. How to use the frequency functions to get current MCG frequency. 3. Work flow Boot to PEE mode from default reset mode Change mode PEE -> PBE ->FBE -> FBI -> BLPI Change back BLPI -> FBI -> FBE -> PBE -> PEE Get System clock in PEE mode to blink LEDIn this example, because the debug console's clock frequency may change,so the example running information is not output from debug console. Here theLED blinks to show that the example finished successfully.