The adc12_interrupt example shows how to use interrupt with ADC12 driver.In this example, user should indicate a channel to provide a voltage signal (can be controlled by user) as the ADC12's sample input.When running the project, typing any key into debug console would trigger the conversion. ADC interrupt would be asserted once the conversion is completed. In ADC ISR, the conversion completed flag would be cleared by reading the conversion result value.Also, the conversion result value is stored, and the ISR counter is increased. These information would be printed when the execution return to the main loop.The point is that the ADC12 interrupt configuration is set when configuring the ADC12's conversion channel. When in software trigger mode, the conversion would be launched by the operation of configuring channel, just like writing a conversion command. So if user wants to generate the interrupt every time the conversion is completed, the channel's configuration with enabling interrupt setting would be used for each conversion.

The adc12_lpit_trgmux example shows how to use the LPIT and TRGMUX to generate a ADC trigger.In this example, user should indicate a channel to provide a voltage signal (can be controlled by user) as the ADC12'ssample input. When run the example, the ADC is triggered by TRGMUX and gets the ADC conversion result in the ADCConversion Complete (COCO) Interrupt. The LPIT is configured as periodic counter which will output pre-trigger andtigger signal to TRGMUX periodically.

The adc12_polling example shows the simplest way to use ADC12 driver.In this example, user should indicate a channel to provide a voltage signal (can be controlled by user) as the ADC12's sample input.When running the project, typing any key into debug console would trigger the conversion. The execution would check the conversion completed flag in loop until the flag is asserted, which means the conversion is completed. Then read the conversion result value and print it to debug console.Note, the default setting of initialization for the ADC converter is just an available configuration. User can change theconfiguration structure's setting in application to fit the special requirement.The auto-calibration is not essential but strongly recommended. It can help to adjust the converter itself and improve theADC12's performance.

CMSIS-Driver defines generic peripheral driver interfaces for middleware making it reusable across a wide range of supported microcontroller devices. The API connects microcontroller peripherals with middleware that implements for example communication stacks, file systems, or graphic user interfaces. More information and usage methord please refer to http://www.keil.com/pack/doc/cmsis/Driver/html/index.html.The cmsis_uart_edma_transfer example shows how to use uart cmsis driver with EDMA:In this example, one uart instance connect to PC through uart, the board willsend back all characters that PC send to the board.Note: The example echo every 8 characters, so input 8 characters every time.

CMSIS-Driver defines generic peripheral driver interfaces for middleware making it reusable across a wide range of supported microcontroller devices. The API connects microcontroller peripherals with middleware that implements for example communication stacks, file systems, or graphic user interfaces. More information and usage methord please refer to http://www.keil.com/pack/doc/cmsis/Driver/html/index.html.The cmsis_uart_interrupt_transfer example shows how to use uart cmsis driver in interrupt way:In this example, one uart instance connect to PC through uart, the board willsend back all characters that PC send to the board.Note: The example echo every 8 characters, so input 8 characters every time.

The CRC Example project is a demonstration program that uses the KSDK software to generate checksumsfor an ASCII string. Several CRC protocols are implemented using the CRC driver API.

The EDMA memory to memory example is a simple demonstration program that uses the SDK software.It excuates one shot transfer from source buffer to destination buffer using the SDK EDMA drivers.The purpose of this example is to show how to use the EDMA and to provide a simple example fordebugging and further development.

The EDMA memory to memory example is a simple demonstration program that uses the SDK software.It excuates one shot transfer from source buffer to destination buffer using the SDK EDMA drivers.The purpose of this example is to show how to use the EDMA and to provide a simple example fordebugging and further development.

The flexnvm_dflash example shows how to use flash driver to operate data flash:

The flexnvm_eeprom example shows how to use flash driver to operate eeprom: