The EDMA memory to memory example is a simple demonstration program that uses the SDK software.It excuates one shot transfer from source buffer to destination buffer using the SDK EDMA drivers.The purpose of this example is to show how to use the EDMA and to provide a simple example fordebugging and further development.

The enet_rxtx_ptp1588 example shows the way to use ENET driver to receive and transmit frame in the 1588 feature required cases.1. This example shows how to initialize the ENET MAC.2. How to use ENET MAC to receive and transmit frame.3. How to add to the multicast group to receive PTP 1588 message.4. How to get the time stamp of the PTP 1588 timer.4. How to use Get the ENET transmit and receive frame time stamp.The example transmits 20 number PTP event frame, shows the timestamp of the transmitted frame.The length, source MAC address and destination MAC address of the received frame will be print. The time stamp of the received timestamp will be print when the PTP message frame is received. Note, The RMII mode is used for default setting to initialize the ENET interface between MAC and the external PHY. you can change it to MII mode as you wish. Please make sure the MII Mode setting in the MAC is synchronize to the settingin TWR-SERIAL board for the external PHY.

The enet_rxtx example shows the simplest way to use ENET driver for simple frame receive and transmit.1. This example shows how to initialize the ENET MAC.2. How to use ENET MAC to receive and transmit frame.The example transmits 20 number broadcast frame, print the frame length, source MAC addressand destination MAC address when receive frame.Note, The RMII mode is used for default setting to initialize the ENET interface between MAC and the external PHY. youcan change it to MII mode as you wish. Please make sure the MII Mode setting in the MAC is synchronize to the settingin TWR-SERIAL board for the external PHY.

The EWM Example project is to demonstrate usage of the KSDK EWM driver.In the example, EWM counter is continuously refreshed until button is pressed.Once the button is pressed, EWM counter will expire and interrupt will be generated.After the first pressing, another interrupt can be triggered by pressing button again.

The flexcan_loopback_functional example shows how to use the loopback test mode to debug your CAN Bus design:To demonstrates this example, only one board is needed. The example will config one FlexCAN MessageBuffer to Rx Message Buffer and the other FlexCAN Message Buffer to Tx Message Buffer with same ID.After that, the example will send a CAN Message from the Tx Message Buffer to the Rx Message Bufferthrouth internal loopback interconnect and print out the Message payload to terminal.

The flexcan_loopback example shows how to use the loopback test mode to debug your CAN Bus design:To demonstrates this example, only one board is needed. The example will config one FlexCAN MessageBuffer to Rx Message Buffer and the other FlexCAN Message Buffer to Tx Message Buffer with same ID.After that, the example will send a CAN Message from the Tx Message Buffer to the Rx Message Bufferthrough internal loopback interconnect and print out the Message payload to terminal.

The FTM project is a demonstration program of generating a combined PWM signal by the SDK FTM driver. It sets up the FTMhardware block to output PWM signals on two TPM channels. The example also shows the complementary mode of operationand deadtime insertion.On boards that have 2 LEDs connected to the FTM pins, the user will see a change in LED brightness.And if the board do not support LEDs to show, the outputs can be observed by oscilloscope.

The FTM project is a demonstration program of the SDK FTM driver's dual-edge capture feature.This feature is available only on certain SoC's.The example sets up a FTM channel-pair for dual-edge capture. Once the input signal is received,this example will print the capture values and period of the input signal on the terminal window.

The FTM project is a demonstration program of the SDK FTM driver's input capture feature.The example sets up a FTM channel for dual-edge capture. Once the input signal is received,this example will print the capture value.

The FTM project is a demonstration program of the SDK FTM driver's output compare feature.It sets up one FTM channel to toggle the output when a match occurs with the channel value. The usershould probe the FTM output with a oscilloscope to see the signal toggling.